dailyspect 
Nowadays, there are so many products of pentek cold water filter in the market and you are wondering to choose a best one. You have searched for pentek cold water filter in many merchants, compared about products prices & reviews before deciding to buy them.
You are in RIGHT PLACE.
Here are some of best sellings pentek cold water filter which we would like to recommend with high customer review ratings to guide you on quality & popularity of each items.
43,964 Reviews Scanned
Pentek EPM-20BB Carbon Block Filter Cartridge, 20" x 4-5/8", 10 Microns
- none
- Imported
- Reduces fine sediment and chlorine taste and odor in residential and commercial drinking water
- Nominal filtration rating of 10 microns
- Bonded PAC media with polyolefin pre-filter and polyethylene netting for extended life
- Initial pressure drop of 4 psi at a flow rate of 4 gpm
- Temperature range of 40 to 180 degrees F (4.4 to 82.2 degrees C)
This Pentek EPM-20BB carbon block filter cartridge reduces fine sediment and chlorine taste and odor in residential and commercial drinking water. It has a nominal (85%) filtration rating of 10 microns. The filter will reduce free available chlorine (FAC) at 2 parts per million (ppm) by at least 90% in up to 30,000 gallons at a flow rate of 4 gallons per minute (gpm). This cartridge is made of bonded powdered activated carbon (PAC) filter media wrapped in polyolefin with polyethylene outer netting. The nitrile butadiene rubber (Buna-N) gaskets seal the cartridge against the housing (sold separately). The cartridge has an initial pressure drop of 4 pounds per square inch (psi) at a flow rate of 4 gallons per minute (gpm), and operates over a temperature range of 40 to 180 degrees F (4.4 to 82.2 degrees C). This carbon block filter cartridge meets National Sanitation Foundation/American National Standards Institute (NSF/ANSI) standard 42 for quality assurance, and is used for purification of residential and commercial drinking water.
Specifications
| Nominal filtration rating | 10 microns |
| Initial pressure drop at 4 gpm | 4 psi |
| Chlorine reduction capacity | 30,000 gallons at 4 gpm |
| Temperature range | 40 to 180 degrees F (4.4 to 82.2 degrees C) |
| Maximum dimensions (H x W) | 20 x 4-5/8 inches (508 x 118 mm) |
| Materials certification | NSF/ANSI standard 42 |
The nominal filtration rating is for a particle removal efficiency of 85%. Chlorine reduction capacity is the minimum total amount of water for which the free available chlorine (FAC) at a concentration of 2 ppm is reduced by at least 90%.
H is height, the vertical distance from lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.
Water filters remove undesirable particles, chemicals, and microorganisms from water by means of a semipermeable barrier, adsorption, or biological processes. They are made of densely packed synthetic or natural fibers that trap suspended particles, materials that block microbes or adsorb unwanted chemicals, or substances that cause a chemical change, such as acid neutralization. For most residential, commercial, and industrial applications, water filters are manufactured in the form of replaceable cartridges that fit inside permanent housings. Filtration systems typically consist of a series of two or more types of filters, each designed to remove different contaminants. The performance of filters is measured by the minimum particle size that is blocked, the percentage of particles or microorganisms that are removed, the downstream concentration of unwanted chemicals, the maximum flow rate, and the amount of water that can be filtered before the filter must be replaced. Water filters are used in a wide range of applications, including drinking water purification, swimming pools, industrial processes, and irrigation, among others.
Pentair manufactures industrial, commercial, and residential water filtration components and systems. The company, founded in 1966 and headquartered in Minneapolis, MN, meets International Organization for Standardization (ISO) standards 9001 and 14001 for quality assurance.
Similar items with 4 stars and above
Pentek 158643 3/8" #10 3G Slim Line Clear Filter Housing with Bracket and Pressure Relief
- Slim filter housing for low-flow applications with space restrictions
- Clear styrene-acrylonitrile (SAN) for on-site viewing of flow and cartridge condition
- Holds a 10″ x 2-1/2″ sediment or carbon filter cartridge (sold separately)
- Pressure relief button for easier cartridge replacement
- Initial pressure drop of 2 psi at a flow rate of 5 gpm
This Pentek 158643 3/8″ #10 3G Slim Line clear filter housing with integrated mounting bracket and pressure relief is suitable for low flow rate applications that have space restrictions. The sump is made of clear styrene-acrylonitrile (SAN) for on-site viewing of flow and cartridge condition, and the cap is made of reinforced blue polypropylene for strength and resistance to chemicals. The cap has 3/8″ female National Pipe Thread Taper (NPT) threaded input and output connections and a nitrile butadiene rubber (Buna-N) O-ring to ensure a watertight seal. A pressure relief button on the inlet side of the cap releases pressure in the housing for changing filter cartridges. The housing can be used with a 10″ x 2-1/2″ sediment or carbon filter cartridge (sold separately). It has an initial pressure drop of 2 pounds per square inch (psi) at a flow rate of 5 gallons per minute (gpm), a maximum operating pressure of 125 psi, and a maximum operating temperature of 125 degrees F (51.7 degrees C). This filter housing meets National Sanitation Foundation/American National Standards Institute (NSF/ANSI) standard 42 for quality assurance, and is for use in various applications, including residential drinking water filtration, food service, and humidifying systems, among others.
Specifications
| Filter cartridge size (H x W) (sold separately) | 10 x 2-1/2 inches (254 x 63.5 mm) |
| Initial pressure drop at 5 gpm | 2 psi |
| Maximum temperature | 125 degrees F (51.7 degrees C) |
| Maximum pressure | 125 psi |
| Maximum dimensions (H x W) | 13-3/8 x 5-3/8 inches (340 x 137 mm) |
| Materials and structural integrity certification | NSF/ANSI standard 42 |
H is height, the vertical distance from lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.
Water filters remove undesirable particles, chemicals, and microorganisms from water by means of a semipermeable barrier, adsorption, or biological processes. They are made of densely packed synthetic or natural fibers that trap suspended particles, materials that block microbes or adsorb unwanted chemicals, or substances that cause a chemical change, such as acid neutralization. For most residential, commercial, and industrial applications, water filters are manufactured in the form of replaceable cartridges that fit inside permanent housings. Filtration systems typically consist of a series of two or more types of filters, each designed to remove different contaminants. The performance of filters is measured by the minimum particle size that is blocked, the percentage of particles or microorganisms that are removed, the downstream concentration of unwanted chemicals, the maximum flow rate, and the amount of water that can be filtered before the filter must be replaced. Water filters are used in a wide range of applications, including drinking water purification, swimming pools, industrial processes, and irrigation, among others.
Pentair manufactures industrial, commercial, and residential water filtration components and systems. The company, founded in 1966 and headquartered in Minneapolis, MN, meets International Organization for Standardization (ISO) standards 9001 and 14001 for quality assurance.
Similar items with 4 stars and above
Pentek GAC-10 Drinking Water Filter (9-3/4" x 2-7/8")
The PENTEK-GAC-10 cartridge provides effective reduction of chlorine and bad taste and odor from your drinking water. The filter cartridge is manufactured to prevent channeling or bypass and maximize contact with the filter media. The innovative post-filter reduces carbon fines before the water leaves the cartridge for cleaner, better tasting drinking water. Ideal for general-purpose water filtration..
Similar items with 4 stars and above
Pentek PCC212 Phosphate Filter Cartridge, 9-3/4" x 2-5/8"
- Inhibits scale and rust buildup in residential and commercial applications
- Prevents staining caused by precipitating iron
- Food-grade hexametaphosphate media
- Initial pressure drop of 1 psi at a flow rate of 1.5 gpm
- Temperature range of 40 to 100 degrees F (4.4 to 37.8 degrees C)
This Pentek PCC212 phosphate filter cartridge inhibits scale and rust buildup and prevents the precipitation of dissolved rust in residential and commercial applications. It is made of sodium calcium hexametaphosphate crystal media in a polypropylene shell with a polypropylene post-filter. The nitrile butadiene rubber (Buna-N) gaskets seal the cartridge against the housing (sold separately). The filter has an initial pressure drop of 1 pound per square inch (psi) at a flow rate of 1.5 gallons per minute (gpm), and operates over a temperature range of 40 to 100 degrees F (4.4 to 37.8 degrees C). This phosphate filter cartridge is used in various applications, including ice machines, food service equipment, and air conditioners, among others .
Specifications
| Filter housing size | Pentek #10 Slim Line or Standard |
| Initial pressure drop at 1.5 gpm | 1 psi |
| Temperature range | 40 to 100 degrees F (4.4 to 37.8 degrees C) |
| Maximum dimensions (H x W) | 9-3/4 x 2-5/8 inches (248 x 67 mm) |
H is height, the vertical distance from lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.
Water filters remove undesirable particles, chemicals, and microorganisms from water by means of a semipermeable barrier, adsorption, or biological processes. They are made of densely packed synthetic or natural fibers that trap suspended particles, materials that block microbes or adsorb unwanted chemicals, or substances that cause a chemical change, such as acid neutralization. For most residential, commercial, and industrial applications, water filters are manufactured in the form of replaceable cartridges that fit inside permanent housings. Filtration systems typically consist of a series of two or more types of filters, each designed to remove different contaminants. The performance of filters is measured by the minimum particle size that is blocked, the percentage of particles or microorganisms that are removed, the downstream concentration of unwanted chemicals, the maximum flow rate, and the amount of water that can be filtered before the filter must be replaced. Water filters are used in a wide range of applications, including drinking water purification, swimming pools, industrial processes, and irrigation, among others.
Pentair manufactures industrial, commercial, and residential water filtration components and systems. The company, founded in 1966 and headquartered in Minneapolis, MN, meets International Organization for Standardization (ISO) standards 9001 and 14001 for quality assurance.
Pentek 151120 Buna-N O-ring for Standard & 3G Standard Housings
(Package Of 3) Pentek C-1 Carbon Water Filters (9.75" x 2.5")
Pentek C-1 Water Filter Replacement Information: Easy to install in whole house water filter systems, reverse osmosis systems, or recreational vehicle systems Pentek C-1 Water Filter Equivalent Brands: The following Culligan water filter models hold this sediment water filter cartridge: HF-150, HF-160, HF-360, HF-365 The following Ametek, USFilter, and Plymouth Products models hold this sediment water filter cartridge: #10 Blue, #10 Clear The Pentek C1 water filter also fits Cuno, AquaPure, Omni, Sears, Fulflo, Teledyne Water Pik, Ace, Master Plumber, Flotec, Honeywell, General Electric, American Plumber, and most other water filter housings for 10" x 2.5" filters The Pentek C-1 is the same as the Ametek C1, Culligan C-1, USFilter C-1, Pentek C-1, American Plumber C-1, Plymouth Products C-1, or Kleen Plus C1. Ametek # 155002 is the same as the Pentek C1 water filter. .Pentek C1 Carbon Water Filter Cartridge Specs: Dimensions:9.75" x 2.5" (248 mm x 64mm) Micron Rating (Nominal):5 Micron Temperature Rating: 40?F to 125?F (4.4? C to 51.7?C) Initial ∆P (psi) @ Flow Rate (gpm): 4 psi @ 5 gpm (0.3 bar 19 L/min) Chlorine Taste & Odor Reduction @ Flow Rate (gpm): >2,500 gallons @ 1 gpm (>9,500 liters @ 3.8 L/min)NOTE: Estimated capacity tested at given flow rate using 2 ppm free available chlorine to 0.5 ppm breakthrough. Pentek C1 Carbon Filter Materials of Construction: Filter Media:PAC Impregnated Cellulose End Caps:Vinyl Plastisol Netting:Polyethylene Core:Polypropylene Reinforcement Backing:Cellulose Polyester (Package Of 3)
Pentek C1 Carbon Filter Cartridge, 9-3/4 x 2-1/2, 5 Micron (4, 1 Pack)
- Qty. 4 of Pentek 155002-43
- General purpose taste & odor reduction for residential chlorinated water supplies
- High flow rates possible due to low initial pressure drop
- Good dirt-holding capacity
- Constructed of a carbon-impregnated cellulose media, these dual-purpose cartridges filter out fine sediment particles and reduce unwanted taste, odor, and chlorine taste & odor from your tap water. A polyester reinforcement backing and external netting provide additional strength and dirt-loading capacity.
Pentair’s Pentek C Series carbon filter cartridges offer an economical solution for all your general purpose water filtration needs. Constructed of a carbon-impregnated cellulose media, these dual-purpose cartridges filter out fine sediment particles and reduce unwanted taste, odor, and chlorine taste & odor from your tap water. A polyester reinforcement backing and external netting provide additional strength and dirt-loading capacity. Recommended for chlorinated water supplies.
24 pk Pentek 155014-43, P5 9-3/4" x 2-3/8" 5 Micron Sediment Melt Blown Filters Cartridges Spun Polypropylene
- Fits 9.75″ x 2.5″ Filter Housing. Referred to as a Standard 10″ Replacement Sediment Filter, i.e. 5 Micron Sediment Filter also referred to as Replacement Sediment Filter for a 9.75″ x 2.5″ Standard Housing. Applications: (Liquids) Whole House or Building Sediment Filtration, Reverse Osmosis Systems Filtration Systems, Prestage Filtration for: Food and beverages, Oil and gas, Fine chemicals, Electronics, Metal finishing, Pulp and paper, Manufacturing, Laboratory, Medical & Scientific Purposes, to name a few
- Meets FDA requirements for food and beverage contact Measurements:
- Brand name: Pentek
- Country of Origin: Mexico
- Item Dimensions: 10.25″L x 10.75″W x 15.75″H
24 Pack of 5 Micron 10″ replacement sediment filters. Pentek Brand FITS BUT NOT LIMITED TO: Ametek, Brio, Culligan, Cuno, Cuno Aqua-Pure, Flowmatic, GE, Glacier Bay hdg2vs4, KemFlo, Kenmore, Omni, 3M Purification, Pentek, Pentek Heavy Duty 10″ Filter Housings, Pentek 3G Heavy Duty 10″ Filter Housings, Pentek 3G Heavy Duty 10″ Filter Housings, Sears, US Filter, Watts/Flowmatic Standard 10″ Filter Housings, Whirlpool: WHKF-GD05, WHKF-DWHV, WHKF-DWH, WHKF-DUF, and many more. Multi Versatile, Individually Wrapped, with Genuine Brio Certified Sterile Packaging. 5 Micron Rating, NSF Certified. Meets FDA requirements for food and beverage contact. Greater dirt holding ability and longer life than non-layered cartridges. Great for Whole Home, Wells, Reverse Osmosis Pre-Stage or Stage One Filtration Quality Water Begins With High Quality Sediment Filtration, Gold Metal Winner, (See description below for some of the compatible filter housings of this product)
Pentek P5 Spun Polypropylene Filter Cartridge, 9-3/4" x 2-3/8", 5 Microns
- Reduces sand, silt, scale, and rust particles in residential, commercial, and municipal drinking water
- Nominal filtration rating of 5 microns
- Spun polypropylene for resistance to chemicals and bacteria
- Initial pressure drop of 0.2 psi at a flow rate of 5 gpm
- Temperature range of 40 to 145 degrees F (4.4 to 62.8 degrees C).
This Pentek P5 spun polypropylene filter cartridge reduces sand, silt, scale, and rust particles in residential, commercial, and municipal drinking water. It has a nominal filtration rating of 5 microns at an efficiency of 85%. The filter is made of spun polypropylene fibers for resistance to chemicals and bacteria. It has an initial pressure drop of 0.2 pound per square inch (psi) at a flow rate of 5 gallons per minute (gpm), and operates over a temperature range of 40 to 145 degrees F (4.4 to 62.8 degrees C). This spun polypropylene filter cartridge meets National Sanitation Foundation/American National Standards Institute (NSF/ANSI) standard 42 for quality assurance, and is used for treatment of residential, commercial, and municipal drinking water.
Specifications
| Nominal filtration rating | 5 microns |
| Initial pressure drop at 5 gpm | 0.2 psi |
| Temperature range | 40 to 145 degrees F (4.4 to 62.8 degrees C) |
| Maximum dimensions (H x W) | 9-3/4 x 2-3/8 inches (248 x 60 mm) |
| Materials certification | NSF/ANSI standard 42 |
The nominal filtration rating is for a particle removal efficiency of 85%.
H is height, the vertical distance from lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.
Water filters remove undesirable particles, chemicals, and microorganisms from water by means of a semipermeable barrier, adsorption, or biological processes. They are made of densely packed synthetic or natural fibers that trap suspended particles, materials that block microbes or adsorb unwanted chemicals, or substances that cause a chemical change, such as acid neutralization. For most residential, commercial, and industrial applications, water filters are manufactured in the form of replaceable cartridges that fit inside permanent housings. Filtration systems typically consist of a series of two or more types of filters, each designed to remove different contaminants. The performance of filters is measured by the minimum particle size that is blocked, the percentage of particles or microorganisms that are removed, the downstream concentration of unwanted chemicals, the maximum flow rate, and the amount of water that can be filtered before the filter must be replaced. Water filters are used in a wide range of applications, including drinking water purification, swimming pools, industrial processes, and irrigation, among others.
Pentair manufactures industrial, commercial, and residential water filtration components and systems. The company, founded in 1966 and headquartered in Minneapolis, MN, meets International Organization for Standardization (ISO) standards 9001 and 14001 for quality assurance.
Similar items with 4 stars and above
Pentek PD-25-934 Polypropylene Filter Cartridge, 9-7/8" x 2-1/2", 25 Microns
- Reduces sand, silt, scale, and rust particles in commercial drinking water and industrial fluid applications
- Nominal filtration rating of 25 microns
- Bonded polypropylene microfiber for resistance to chemicals and bacteria
- Initial pressure drop of less than 2 psi at a flow rate of 2 gpm
- Temperature range of 40 to 175 degrees F (4.4 to 79.4 degrees C)
This Pentek PD-25-934 polypropylene filter cartridge reduces sand, silt, scale, and rust particles in commercial drinking water and industrial fluid applications. It has a nominal filtration rating of 25 microns at an efficiency of 85%. The filter is made of thermally bonded polypropylene microfibers for resistance to chemicals and bacteria and minimal fiber release. It has an initial pressure drop of less than 2 pounds per square inch (psi) at a flow rate of 2 gallons per minute (gpm), and operates over a temperature range of 40 to 175 degrees F (4.4 to 79.4 degrees C). This polypropylene filter cartridge meets National Sanitation Foundation/American National Standards Institute (NSF/ANSI) standard 42 for quality assurance, and is used for treatment of commercial drinking water and industrial filtration applications.
Specifications
| Nominal filtration rating | 25 microns |
| Initial pressure drop at 2 gpm | <2> |
| Temperature range | 40 to 175 degrees F (4.4 to 79.4 degrees C) |
| Maximum dimensions (H x W) | 9-7/8 x 2-1/2 inches (251 x 64 mm) |
| Materials certification | NSF/ANSI standard 42 |
The nominal filtration rating is for a particle removal efficiency of 85%.
H is height, the vertical distance from lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.
Water filters remove undesirable particles, chemicals, and microorganisms from water by means of a semipermeable barrier, adsorption, or biological processes. They are made of densely packed synthetic or natural fibers that trap suspended particles, materials that block microbes or adsorb unwanted chemicals, or substances that cause a chemical change, such as acid neutralization. For most residential, commercial, and industrial applications, water filters are manufactured in the form of replaceable cartridges that fit inside permanent housings. Filtration systems typically consist of a series of two or more types of filters, each designed to remove different contaminants. The performance of filters is measured by the minimum particle size that is blocked, the percentage of particles or microorganisms that are removed, the downstream concentration of unwanted chemicals, the maximum flow rate, and the amount of water that can be filtered before the filter must be replaced. Water filters are used in a wide range of applications, including drinking water purification, swimming pools, industrial processes, and irrigation, among others.
Pentair manufactures industrial, commercial, and residential water filtration components and systems. The company, founded in 1966 and headquartered in Minneapolis, MN, meets International Organization for Standardization (ISO) standards 9001 and 14001 for quality assurance.
Conclusion
By our suggestions above, we hope that you can found pentek cold water filter for you.Please don’t forget to share your experience by comment in this post. Thank you!
